26-Lb. Countertop Ice Maker User’s Manual PDF

1m ago
1 Views
0 Downloads
3.84 MB
20 Pages
Transcription

26-Lb. CountertopIce MakerUser’s ManualItem #1296908Model #HZB-12/SA

CONTENTSIMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5PARTS AND FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8CARE AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

IMPORTANT SAFETY INSTRUCTIONSWhen using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electricshock, and injury to persons or property. Read all instructions before using any appliance. DO NOT operate this or any other appliance with a damaged cord. Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Besure that the plug is fully inserted into the receptacle. DO NOT run cord over carpeting or other heat insulators. DO NOT cover the cord. Keep cord away fromtraffic areas, and DO NOT submerge in water. We do not recommend the use of an extension cord, as it may overheat and become a fire hazard. If youmust use an extension cord, use No. 14 AWG minimum size and rated no less than 1875 watts. Unplug the ice maker before cleaning or making repairs. Exercise caution and use reasonable supervision when appliance is used near children. DO NOT clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion. DO NOT tip over. If the ice maker is brought indoors from outdoors during the wintertime, give it a few hours to adjust toroom temperature before plugging it in. DANGER: Risk of fire or explosion. Flammable refrigerant used. DO NOT use mechanical devices todefrost ice maker. DO NOT puncture refrigerant tubing. DANGER: Risk of fire or explosion. Flammable refrigerant used. To be repaired only by trained servicepersonnel. DO NOT puncture refrigerant tubing. CAUTION: Risk of fire or explosion. Flammable refrigerant used. Consult repair/owner’s manual beforeattempting to install or service this product. All safety precautions must be followed. CAUTION: Risk of fire or explosion. Dispose of properly in accordance with local or federal regulations.Flammable refrigerant used. CAUTION: Risk of fire or explosion due to puncturing of refrigerant tubing. Follow handling instructionscarefully. Flammable refrigerant used. The ice maker should be installed in accordance with the safety standard for refrigeration systems,ASHRAE15. The ice maker shall not be installed in corridor or hallways of public buildings. If the unit has a problem that needs service or parts replaced, the service must be done by factory authorizedpersonnel to minimize the risk of the refrigerant igniting due to incorrect parts or improper service.READ AND FOLLOW THISSAFETY INFORMATION CAREFULLYSAVE THESE INSTRUCTIONS4

SPECIFICATIONSFigure 114.1” (358 mm)12.9” (328 mm)9.5” (242 mm)Dimensions (W x H x D)9.5” x 12.9” x 14.1” (242 mm x 328 mm x 358 mm)Weight17.0 lbs (7.7 kg)Ice Producing CapacityUp to 26 Lbs a day5

PARTS AND FEATURESFigure 2ehadbcfgSee Through Window(Allows visibility of the interior)d.Ice Scoope.Control Panelb.Ice Full Sensorf.Air Outletc.Ice Basketg.Water Drain Cap(At front underside of the unit)a.6h.Maximum Water Level(Not shown on theunit image above.You can see the waterlevel mark when theice basket is removed.)

INSTALLATION INSTRUCTIONSUnpacking Your Ice Maker1.Remove all exterior and interior packaging. Check that ice basket and ice scoop is included. If any parts oraccessories are missing, please contact customer service.2.Clean the interior with lukewarm water and a soft cloth. Remove the ice basket and wash it in warm water.3.Find a location for your ice maker that is protected from direct sunlight and other sources of heat (i.e.:stove, furnace, radiator). Place the ice maker on a level surface. Make sure that there is at least 5 inches ofspace between the back and sides of your ice maker and the wall.4.Allow one hour for the refrigerant fluid to settle before plugging it in the unit.5.The appliance must be positioned so that the plug is accessible.Connecting your Ice MakerDANGER: Improper use of the grounded plug can result in the risk of electrical shock. If the power cordis damages.1.This unit should be properly grounded for your safety. The power cord if this appliance is equipped witha three-prong plug which connects with standard three prong wall outlets to minimize the possibility ofelectric shock.2.Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under anycircumstances, cut or remove the third (ground) prong from the power cord. Any questions concerningpower and/or grounding should be directed toward a certified electrician.3.This appliance requires a standard 115 Volt, 60 Hz electrical outlet with three prong ground.Note: Before using your ice maker, it is strongly recommended to clean it thoroughly.WARNING: The ice maker is not designed to be installed in an outside area such as a garage or a porch.Ambient temperatures of below 50 F or above 100.4 F will hinder the performance of the appliance.7

OPERATING INSTRUCTIONSCONTROL PANELedcFigure 3faba.Button to turn on/off the unitc.Power Indicatore.Water Shortage Indicatorb.Button to select ice cube sized.Ice Full Indicatorf.Selected ice size: Small or largeBEFORE USE Before connecting the appliance to the power supply, let the unit stand upright for 1 hour, which will reducethe possibility of the cooling system malfunctioning due to improper handling. Clean your unit thoroughly before putting into use. (Refer to “CARE AND MAINTENANCE”.) Use the parts diagram on page 6 to insure proper positioning of internal components.USING YOUR ICE MAKER1.Clean your ice maker thoroughly.2.Open the cover, remove the ice basket and pour normal tap water into tank. Keep water level below thelevel mark.3.Plug in the unit and the power indicator light will blink.4.Press “POWER” on the control panel to begin the ice making cycle. The power indicator light will light.5.Select the size of the ice cube by pressing the “SELECT” button. If ambient temperature is below 60 F, it isrecommended to select small size to avoid ice sticking together.6.While the icemaker is on, check water level periodically. If water pump cannot inject water, the ice makerwill stop automatically, and the “WATER” indicator will be on. Press the “POWER” button, fill water up tothe level mark and press “POWER” again. Allow 3 minutes for the refrigerant to settle before restarting.7.The ice maker automatically stops working when the ice basket is full and the “ICE FULL” indicator will beilluminated.WARNING: Direct or reflected sunlight may cause the infrared sensor to malfunction. If the unit doesn't stopmaking ice, even when full, move the unit where there is no sunlight.Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level. If unit is not in use, drainall water in the tank reservoir.8

care and MaintenanceHow to Clean1.Remove the ice basket.2.Remove the drain plug from the front underside to drain the water.3.Clean the interior with diluted detergent, warm water and a soft cloth.4.The outside of the ice maker should be cleaned regularly with a mild detergent solution and warm water.5.Dry the interior and exterior with a soft cloth.6.Put back the drain plug.7.When the machine is not in use, open water drain cap to drain water completely from water reservoir.Care and Maintenance The ice maker should be cleaned on a regular basis. It is necessary to have an adequate ventilation space around the ice maker in order to sustain properperformance, dissipation of heat, maintain efficiency, and low power consumption. Clearance of minimum 5inches should be maintained at the rear and sides of the unit and 8 inches at the top of the unit. To attain proper performance, be sure to plug the appliance into a properly grounded 115/60 Hz outlet. Do not modify the power cord under any circumstances to allow the unit to be plugged into a nongrounded outlet. To avoid heat damage to the power cord, please ensure that it does not come in proximityor in direct contact with the compressor of the ice maker. Pleas avoid installing the ice maker in a location where the appliance will come in contact with water ormoisture to minimize rusting of metal parts. The ice maker should not be installed near any heat source or in a location where it will come in directcontact with the sunlight.9

TROUBLESHOOTINGProblemPossible CauseSolution“Add Water”indicator is on.Lack of water.Stop the ice maker, gill water, and press “Power”button again to restart the unit.“Ice” indicatoris on.Ice basket is full.Remove ice from ice basket or continuously press“Select” button 5 seconds. The unit could makeice 10 cycles even “Ice” indicator is on.“Water” and “Ice”indicators are bothilluminated.Ice shovel is stuck.Check if ice is blocking the ice shovel, otherwiseconsult a certified technician.Ice making cycle is too long.Stop the ice maker, and restart when the iceblocks melt. Select the small ice size.Water temperature in inner tank is too low.Change the water in the reservoir. Use waterbetween 45 F-90 F.Leaving ice in the appliance for an extendedperiod of time may result in the appliancerecycling the ice by melting it down and makinga new batch.Transfer ready-made ice to another container andstore in a cooler or freezer to avoid recycling.Leaving ice in the appliance for an extendedperiod of time may result in the appliancerecycling the ice by melting it down and makinga new batch.After extended period transfer ready-made ice toanother container and store in a cooler of freezerto avoid recycling.Ambient temperature or water temperature ininner tank is too high.Operate the ice maker below ambient temperatureof 90 F and use cold water.Refrigerant liquid leakage.Consult a qualified technician.Pipe in the cooling system is blocked.Consult a qualified technician.Ice cubes sticktogether.Ice cubes aremelting.Ice making cycle isnormal but no iceis made.10

Máquina de hacer hielode encimeraManual del usuarioArt culo #1296908Modelo #HZB-12/SA

ÍNDICEINSTRUCCIONES DE SEGURIDAD IMPORTANTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13ESPECIFICACIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14PIEZAS Y FUNCIONES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15INSTRUCCIONES DE INSTALACIÓN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16INSTRUCCIONES DE FUNCIONAMIENTO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17CUIDADO Y MANTENIMIENTO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18SOLUCIÓN DE PROBLEMAS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1912

INSTRUCCIONES DE SEGURIDAD IMPORTANTESCuando se utilizan electrodomésticos, se deben observar ciertas medidas de precaución para reducir el riesgode incendios, golpes de corriente y lesiones a las personas o daños a la propiedad. Leer atentamente todas lasinstrucciones antes de usar cualquier electrodoméstico. No poner en funcionamiento ningún electrodoméstico que tenga el cable dañado. Conectar solamente en tomacorrientes debidamente polarizados. No se debe conectar ningún otro artefactoen el mismo tomacorriente. Verificar que el enchufe esté correctamente colocado en el tomacorriente. No dejar el cable extendido sobre la alfombra ni sobre ningún otro aislante térmico. No cubrir el cable.Mantener el cable fuera del área de circulación y no sumergir en agua. No se remomienda el uso de cables de prolongación ya que se pueden recalentar y causar un incendio. Si serequiere el uso de un cable de prolongación, usar N. 14 AWG tamaño mínimo especificado para 1875 Watts,por lo menos. Desenchufar la máquina antes de limpiar o efectuar reparaciones. Tener extrema precaución y adoptar razonables medidas de seguridad cuando se use el electrodomésticoen presencia de niños. No limpiar la máquina con líquidos inflamables. Los vapores pueden originar un incendio o explosión. No inclinar ni volcar. Si en la temporada de invierno la fabricadora que estaba en el exterior se coloca en el interior, se debe dejardescansar algunas horas hasta que adquiera temperatura ambiente antes de enchufar. PELIGRO: Riesgo de incendio o explosión. Contiene refrigerante inflamable. NO utilice dispositivosmecánicos para descongelar la maquina de hacer hielo. NO perfore los tubos de refrigerante. PELIGRO: Peligro de incendio o explosión. Usa refrigerante inflamable. Debe ser reparado por personalde servicio cualificado. NO perfore los tubos de refrigerante PRECAUCION: Peligro de incendio o explosión. Usa refrigerante inflamable. Consultar con Reparación/Manual del propietario antes de intentar instalar este producto o servicio. Todas las precauciones deseguridad deben ser seguidas. PRECAUCION: Peligro de incendio o explosión. Deseche correctamente de acuerdo con las regulacionesfederales o locales. Utiliza refrigerante inflamable. PRECAUCION: Peligro de incendio o explosión debido a perforar los tubos de refrigerante. Sigacuidadosamente las instrucciones de manipulación. Utiliza refrigerante inflamable. La maquina de haver hielo debe ser instalada de acuerdo con la norma de seguridad para los sistemas derefrigeración, ASHRAE15. La maquina de hacer hielo no debe ser instaladan en el corredor o en los pasillosde los edificios públicos. Si la unidad tiene un problema que necesita servicio o piezas sustituidas, el servicio debe ser realizado porpersonal autorizado de fábrica para minimizar el riesgo de avivar el refrigerante debido al incorrecto oinadecuado de piezas de servicio.LEA ESTA INFORMACIÓN DESEGURIDAD Y SÍGALA CUIDADOSAMENTEGUARDE ESTAS INSTRUCCIONES13

ESPECIFICACIONESFigure 114.1” (358 mm)12.9” (328 mm)9.5” (242 mm)9.5” x 12.9” x 14.1” (242 mm x 328 mm x 358 mm)Peso17.0 lbs (7.7 kg)Capacidad de producción de hieloHasta 26 libras al día14

PIEZAS Y FUNCIONESFigure 2ehadbcfgCon ventana que permitever el interiord.Cuchara para hieloePanel de controlb.Sensor full hielof.Salida de airec.Canasta para hielog.Tapón de drenaje de agua(En la part

Remove the ice basket and wash it in warm water. 3. Find a location for your ice maker that is protected from direct sunlight and other sources of heat (i.e.: stove, furnace, radiator). Place the ice maker on a level surface. Make sure that there is at least 5 inches of space between the back and sides of your ice maker and the wall. 4.